Category Archives: Manufacturing Plant

Manufacturing, Manufacturing Plant

Flat Rock, MI – Storage fire at auto assembly plant controlled with help from single sprinkler

A fire that started in storage racks damaged the north side of the Flat Rock Auto Assembly Plant Tuesday night, causing hundreds of workers to be evacuated from the building. Firefighters from Flat Rock, Rockwood and Woodhaven responded to the plant at Gibraltar Rd. and I-75 about 7 p.m. Tuesday.  Firefighters could see smoke billowing from the plant at the Flat Rock station, Chief William Vack said.

“When we arrived, it was going pretty good, and you could see smoke about 100 feet in the air,” Chief Vack said afterward. “Once we got our water supplies established, we had it knocked down in about a half hour.”

Where the fire started was only about 100 feet from Vreeland Rd., he said. Heat from the fire penetrated an exterior wall on the north side of the plant, activating a single sprinkler in a newer section of the building, he said. The sprinkler helped quell any fire inside.

“Most of the plant was unaffected,” Chief Vack said. “The fire was near the truck docks. … There was no smoke in the building.”

He said it was standard procedure to evacuate the plant when a fire alarm is activated. The amount of damage was unknown but was not believed to be extensive. Firefighters were on the scene for about two hours.

Manufacturing, Manufacturing Plant

Danville, VA – Damage from fire at flooring manufacturer minimized thanks to sprinkler system

Smoke poured out of the loading dock doors in one of the plants at Columbia Flooring on Maxine Road as Danville firefighters arrived in response to a reported fire at about 7 p.m.

About an hour later, sweating and parched firefighters gathered near one of the six engines at the scene, to wrap their heads in wet towels and drink water or energy drinks — the fire was considered under control, Fire Marshall Shelby Irving said, though smoke still billowed out of the loading dock doors.

As firefighters began carrying fans toward the building to help clear the smoke, Irving said it was impossible to look for the cause of the fire until the smoke was cleared.

“There’s so much smoke in there you can’t see anything,” Irving said.

But the sprinkler system in the plant had done its job, Irving said.

“The sprinklers did activate and keep the fire in check,” Irving said. “Because of that, the [firefighters] were able to get in there pretty quick and get a line on the fire … the damage will be much less than it could have been.”

The fire was in a production area of the plant and caused extensive damage to machinery and electrical equipment, according to a news release. This section of the plant will be closed for two to three days. 

Manufacturing, Manufacturing Plant

Spring Hill, TN – Sprinkler system helps contain blaze at GM plant; welding sparks likely cause of fire

About 240 workers were evacuated from the General Motors Spring Hill Manufacturing Facility on Wednesday after a fire broke out on the third floor of one of its production buildings.

Six Columbia and four Spring Hill fire trucks responded to the scene, Columbia Assistant Fire Chief Tim Holt said.

Firefighters received the call at 3:03 p.m. and rushed to GM’s body shop off Nashville Highway and Saturn Parkway.

Crews found an air-handling machine on fire, spreading smoke in the building, Holt said.

“We got it knocked down quickly, within 15 minutes,” Holt said. “The sprinkler system helped keep the fire in place.”

One GM security guard on the scene was treated for smoke inhalation, he said.

The incident likely was caused by welding sparks, which caught cardboard on fire, Holt said.

Columbia’s fire department had 16 firefighters on scene.

GM spokesman Tom W. Wickham said the body shop was closed for the rest of Wednesday evening and will reopen Thursday morning.

“We had to clean up a lot of water and debris,” Wickham said.

A similar incident brought fire crews to the GM plant just after midnight May 20. No one was hurt then, but the building was evacuated.

Manufacturing, Manufacturing Plant

Forks Township, PA – Polystyrene fire at plastics manufacturer controlled by sprinkler system

A Sunday morning fire at a Forks Township manufacturer could have been much worse if not for the building’s sprinkler system, a township fire official said. Crews were called for the fire at about 12:15 a.m. at the Ecopax building, 3600 Glover Road, said Matt Mowrey, deputy chief for the Forks Township Fire Department.

Ecopax manufactures foam and plastic food containers. A commercial roll of polystyrene caught fire, leading to a working blaze, but the flames were kept from spreading by the building’s sprinklers, Mowrey said.  The cause of the fire has not yet been determined, and the blaze is under investigation, Mowrey said.

Manufacturing, Manufacturing Plant

Clearfield, UT – Sprinkler system suppresses fire at trailer manufacturer

 A destructive structure fire was avoided early Saturday morning due to a business’s water suppression system.  At 8:11 a.m., North Davis Fire District responded to a fire alarm at trailer manufacturer, Utility Trailer, in Clearfield, located at 1111 S. 1000 West. When crews arrived, water and smoke were coming from the east side of the building, according to a press release from North Davis Fire District.

About 500 employees working at the time, had already been evacuated and set up outside at meeting points designated by Utility Trailer.  Firefighters found a 40-foot trailer had been destroyed by the blaze. The release states the sprinkler system in the building kept the flames from expanding.

There was damage to two trailers: one by fire and the other by water from the sprinkler system, according to the release.  The cost of damage was estimated at $50,000.  “If not for the water suppression system working, this business could have been devastated and could possibly experienced loss of life,” the release states.

Manufacturing, Manufacturing Plant

Apple Valley, CA – Fire at cement plant held in check by sprinkler system

A blaze that erupted at a local cement plant injured two firefighters before it was extinguished early Tuesday morning. Apple Valley Fire Protection District Fire Marshal Jason Nailon told the Daily Press the flames took about an hour to extinguish. The fire was believed to have been caused by possible static or dust explosions at the plant, but remains under investigation.

Reports of a blaze at a building in the Cemex plant in the 25200 block of Black Mountain Quarry Road were received around 2:30 a.m. Tuesday, authorities said. Nailon said the blaze involved the plant’s alternate fuels that power their kilns, which are made up of wood chips, pistachio shells and tire chippings.

It is believed a minor explosion started the blaze, but the building’s sprinkler system kept the fire in check until firefighters arrived. “When we got there, the fire was almost out because of the sprinklers,” Nailon said, “but the rafters appeared to be burning. It turned out to be an accumulation of dust up on the rafters that was still burning.”

About 17 to 20 firefighters responded, including four engines from AVFPD and two from the San Bernardino County Fire Department. It took about an hour to bring the fire under control, Nailon said.

One firefighter reported an ankle injury while another suffered from heat exhaustion while combating the blaze. Nailon said some Cemex employees were at the site as well, but they reported no injuries. Estimated damages to the building are not yet known, but Nailon said the concrete construction and sprinkler system protected the building from further damage.

Manufacturing, Manufacturing Plant

Ellensburg, WA – Business owner thankful that sprinklers helped stop fire at wood products company

A sprinkler system and quick response by firefighters helped limit damage from a fire at Wood Products Northwest in Ellensburg on Tuesday night.

It was caused by spontaneous combustion of rags soaked in oil-based paint.

Kittitas Valley Fire and Rescue received an alarm call about a sprinkler activation at 11:15 p.m. Tuesday at 409 S. Water St. KVFR Deputy Chief Rich Elliott said the department upgraded the alarm to a full response, and found a fire in a room used for cabinet finishes.

“The sprinkler system activated and was keeping the fire under control,” he said.

No one was in the building at the time.

Robert Hamlin, who owns the business with his wife, said he is thankful the sprinklers and fire alarm activated and for KVFR’s quick response.

When he arrived on scene at about midnight, much of the fire was already out, he said.

The fire was in the back of the business’ finish department, which has a three-hour firewall.

“Everything went the best it could. This could have been a huge disaster,” he said. “Combustibles, once they get going, can overwhelm the sprinkler system.”

Firefighters extinguished the fire and spent a few hours helping with water removal.

Elliott said the fire was determined to be accidental. Hamlin said he is still figuring out the extent of the damages, but said it appeared to mostly be water damage.

He hopes his 18 employees can return to work within the next 48 hours.

Manufacturing, Manufacturing Plant

Lee’s Summit, MO – Fire in ductwork at semi-conductor facility controlled by sprinkler system

On Saturday, April 30, 2016, at 8:02 p.m., the Lee’s Summit Fire Department responded to a reported structure fire at Diodes/Fabtech, 777 NW Blue Parkway, in the north building of the Summit Technology Campus. An employee called 911 to report a fire on the roof and smoke in their chemical/gas storage room.

When the fire department arrived, a small fire was visible on the roof of the 540,000 square foot, mixed use facility. The building was in the process of being evacuated.   The fire was located on the roof and in the gas scrubber room, on the north side of the building. The gasses are used for the manufacturing of semi-conductors for the electronics industry and the scrubbers process the gasses after they have been used. 

After consulting with facility staff to determine the types of hazardous materials involved, crews made an initial investigation inside of the scrubber room and found a piece of ductwork from a scrubber unit burning in a pipe chase near the deck of the roof. A sprinkler head near the fire had activated and controlled the fire in the chase.

Fire crews finished extinguishing that fire as other crews attacked the fire involving the ductwork on the roof. On the roof, a portion of the ductwork going to an exhaust fan had burned and fallen away leaving burning gasses coming from two scrubber exhaust pipes. Fire crews applied foam and water from the ladder truck to control the fires and protect the exposures around them as the fire department worked with Diodes staff to shut down all of the gasses going into the scrubber.

After the gasses were shut off, both of the fires were extinguished. The fire was under control at 9:37 p.m. Crews monitored the air around area for hazardous materials throughout the incident.

Fire damage was contained to the exhaust duct on the roof and in the pipe chase from the scrubber room to the roof. After the fire was out and air monitoring was complete, all of the buildings tenants were allowed to reoccupy the building.  The cause of the fire is under investigation.

Manufacturing, Manufacturing Plant

Fond du Lac, WI – Sprinklers keep fire from spreading at Mercury Marine

The sprinkler system installed at Mercury Marine stopped a fire from spreading Wednesday night.

At 11:23 p.m., Fond du Lac Fire and Rescue responded to a report of a fire in the dust collector at Mercury Marine Plant 98. Upon arrival, crews found the sprinkler system activated, limiting the spread of the fire. Some smoke was in the building.

The crews entered the building and contained the fire to the dust collection system. Access to the dust collector was difficult, so putting out the fire was time-consuming, firefighters say.

No injuries were reported.

Manufacturing, Manufacturing Plant

Ashwaubenon, WI – Early morning fire at fiberglass manufacturer limited by sprinkler system

No one was inside an Ashwaubenon fiberglass maker when fire broke out early Tuesday morning, according to Ashwaubenon Public Safety.

Firefighters say it appears a some machinery–possibly an air compressor–caught fire in the back of the building, located in the 2900 hundred block of Holmgren Way.

A sprinkler system alerted crews to the fire and prevented the blaze from spreading to the fiberglass material inside the warehouse.

“Actually the contents inside, we had no extension inside to the contents,” said Chief Eric Dunning, Ashwaubenon Public Safety. “If that would’ve caught, we’d still be fighting it right now. The fire stayed with the machinery itself, but with the contents inside there, this could’ve been far worse.”

The building did sustain smoke damage. Crews were entering the business to investigate what caused the equipment to spark a fire.

“Right now, I’m not sure what the estimate cost of the machinery is,” Chief Dunning said. “And then obviously with the heavy smoke, and there’s quite a few of what appears to be fiberglass halls in there, if there were smoke damage to the halls that were inside the facility.”

The chief stressed the importance of having a sprinkler system.

“We’ll take that in the luck category. We’ll take that as a win for us,” Chief Dunning said. “What also helped is we had an active sprinkler system, so the sprinkler system kept things to a minimum, where if the building wasn’t sprinklered it would’ve for sure spread into other contents and we wouldn’t have been alerted until it was coming through the building.”

Holmgren Way and Ramada Way were closed for a brief time near the scene of a fire. The roads reopened after 5 a.m.